No Need to Bore Up! Here Are 5 Effective Ways to Boost Your Scooter’s Acceleration

Illustration of riding a scooter (Source: 100kpj.com)

If you want to boost your scooter’s power so it accelerates faster without doing a bore-up, there are a few simple tips you can apply. 

Besides not requiring major modifications, the cost is also more affordable. Here are some ways to make your scooter’s acceleration stronger without needing a bore-up!

1. Use Lighter Rollers

Illustration of scooter rollers (Source: Astra Otoshop)

Quoted from Motorplus, replacing the rollers with lighter ones is an effective way to improve a scooter’s performance without doing a bore-up.

By reducing the roller weight, the scooter will accelerate faster. However, make sure you only reduce about 2 grams from the factory rollers so it stays balanced.

2. Readjust the Jetting

Illustration of adjusting motorcycle jetting (Source: iNews)

Readjusting the jetting is very important for improving a scooter’s acceleration. If you want to keep the standard air filter, make sure the jetting is set slightly lean. 

However, if you want to use an open filter, the jetting needs to be set richer. This jetting setup is trial and error, so adjust it to match your motorcycle’s characteristics.

3. Increase the Compression Ratio

Illustration of adjusting a scooter’s compression ratio (Source: Astra Otoshop)

Increasing a scooter’s compression ratio can significantly boost engine power. You can feel it across the rev range, from low to high RPM. 

For example, on a Yamaha Mio, you can raise the compression by shaving about 1 to 1.5 mm off the cylinder head. Meanwhile, for a Honda BeAT, replacing the piston with a Honda Vario piston can increase the compression ratio.

4. Replace the Camshaft with a Racing Version

Illustration of a racing camshaft (Source: Radar Banyumas)

Replacing the standard camshaft with a racing camshaft is an easy way to improve a scooter’s performance. 

This modification can be applied, for example, to a Yamaha Mio to maximize its acceleration even further.

5. Modify the Exhaust

Illustration of an aftermarket exhaust (Source: Tokopedia)

To improve exhaust flow, modifying a scooter’s standard exhaust is an option you can take. 

If you do not want to modify the stock exhaust, you can replace it with an aftermarket exhaust that is more efficient at expelling gases, often referred to as a “standard bobok” exhaust.

By applying these tips, you can improve your scooter’s acceleration without spending a lot on a bore-up. Make modifications wisely for the best results.

Another Way to Maximize Your Motorcycle’s Performance!

Here is an additional tip for you if you want to maximize your motorcycle’s performance without doing a bore-up: use a high quality motorcycle battery.

The best choice is, of course, Dynavolt batteries. Dynavolt offers three variants: Nano-Gel, Lithium, and Sodium Ion, each with its own advantages.

The Nano-Gel battery from Dynavolt is the world's first Nano-Gel technology. Thanks to this technology, the Cold Cranking Ampere (CCA) produced is very high. Additionally, the battery has a low self-discharge rate, which extends its lifespan.

Next, there is the Dynavolt Lithium battery, which is commonly used in racing motorcycles and big bikes. The Dynavolt Lithium battery has an even higher CCA, a lighter weight, and is equipped with a digital display.

Lastly, there is the Dynavolt Sodium Ion battery, which is known for its extremely light weight. This battery is also equipped with a Battery Management System (BMS) that prevents the battery from swelling.

In addition, Dynavolt batteries are trusted and used in over 90 countries worldwide. Dynavolt batteries are also used in MotoGP events (Moto2, Moto3, and MotoE) as well as in WSBK.  

Don't hesitate anymore! Use a Dynavolt battery now on your motorcycle! For more information, check out Dynavolt battery products at:

1. Instagram, Facebook, & Tiktok Dynavolt.Ind
2. YouTube DynavoltIndonesia107
3. Shopee Dynavolt Official Store
4. Tokopedia Dynavolt Official Store